View RF5602_1557009.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 18 optimum technology matching? applied gaas hbt ingap hbt gaas mesfet sige bicmos si bicmos sige hbt gaas phemt si cmos si bjt gan hemt functional block diagram rf micro devices?, rfmd?, optimum technology matching?, enabling wireless connectivity?, powerstar?, polaris? total radio? and ultimateblue? are trademarks of rfmd, llc. bluetooth is a trade- mark owned by bluetooth sig, inc., u.s.a. and licensed for use by rfmd. all other trade names, trademarks and registered tradem arks are the property of their respective owners. ?2006, rf micro devices, inc. product description 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. ordering information rf mems ldmos vcc2 vcc2 vreg1 rf in bias vcc rf out rf out rf out vcc1 vreg2 vreg3 pdetect 15 14 13 12 11 10 4 3 2 1 16 9 8 7 6 5 3 rd stage 2 nd stage 1 st stage interstage match interstage match bias detector input match pdown nc gnd gnd RF5602 3.3v to 5.0v, 2.3ghz to 2.7ghz linear power amplifier the RF5602 is a linear power amplif ier ic designed specifically for medium power applications. the device is manufactured on an advanced ingap heterojunction bipolar transi stor (hbt) process, and has been designed for use as the final rf amplifier in 802.11b/g/n access point transmitters. the device is provided in a 3mmx3mmx0.45mm, 16-pin, leadless chip carrier with a backside ground. the RF5602 is designed to maintain linearity over a wide range of supply voltages and power outputs. features ? single 3.3v to 5v supply ? 32db to 34db small signal gain (typ.) ? 2% evm (rms) at 26dbm, 5.0v ? 2% evm (rms) at 25dbm, 4.2v ? 3% evm (rms) at 23.5dbm, 3.3v ? include power detector on die ? multiple frequency ranges applications ? 802.11b/g/n access points ? pcs communication systems ? 2.4ghz ism band applications ? commercial and consumer sys- tems ? wibro 2.3ghz to 2.4ghz band applications ? wlan 2.4ghz to 2.5ghz band applications ? wimax 2.5ghz to 2.7ghz band applications RF5602 3.3v to 5.0v, 2.3ghz to 2.7ghz linear power amplifier, matte-sn (pb-free) finish RF5602wlpck-410 2.4ghz to 2.5ghz wlan fully assembled eval pcb at 5v RF5602wbpck-410 2.3ghz to 2.4ghz wibro fully assembled eval pcb at 5v RF5602wmpck-410 2.5ghz to 2.7ghz wimax fully assembled eval pcb at 5v prelim ds090427 proposed 9 RF56023.3v to 5.0 v, 2.3ghz to 2.7ghz lin- ear power amplifier package style: qfn, 16-pin, 3mmx3mmx0.45mm
2 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. absolute maximum ratings parameter rating unit supply voltage -0.5 to +5.5 v dc dc supply current tbd ma input rf power +10 dbm operating ambient temperature -40 to +85 c storage temperature -40 to +150 c moisture sensitivity tbd parameter specification unit condition min. typ. max. wlan ieee802.11b/g nominal condition t=25 c, v cc =3.3v, 4.2v, and 5v, v reg =2.85v, freq=2450mhz, duty cycle 10 to 100% unless otherwise noted frequency range 2400 2500 mhz compliance ieee802.11g and ieee802.11b output power 26 dbm with a standard ieee802.11g waveform (54mbit/s), v cc =5.0v evm 2 3 % rms, mean ieee802.11b p out tbd dbm acp1 -34 -30 using a standard ieee802.11b waveform at 1mbps acp2 -54 -50 using a standard ieee802.11b waveform at 1mbps output power 25 dbm with a standard ieee802.11g waveform (54mbit/s), v cc =4.2v evm 2 3 % rms, mean ieee802.11b p out tbd dbm acp1 -34 -30 using a standard ieee802.11b waveform at 1mbps acp2 -54 -50 using a standard ieee802.11b waveform at 1mbps output power 23.5 dbm with a standard ieee802.11g waveform (54mbit/s), v cc =3.3v evm 3 3.5 % rms, mean ieee802.11b p out tbd dbm acp1 -34 -30 using a standard ieee802.11b waveform at 1mbps acp2 -54 -50 using a standard ieee802.11b waveform at 1mbps gain 34 db at nominal condition and v cc =5.0v 34 db at nominal condition and v cc =4.2v 34 db at nominal condition and v cc =3.3v gain variation over temperature 1.5 db -10c to +85c input impedance 50 input matched to 50 caution! esd sensitive device. exceeding any one or a combination of the absolute maximum rating conditions may cause permanent damage to the device. extended application of absolute maximum rating conditions to the device may reduce device reliability. specified typical perfor- mance or functional operation of the devi ce under absolute maximum rating condi- tions is not implied. rohs status based on eudirective2002/95/ec (at time of this document revision). the information in this publication is believed to be accurate and reliable. however, no responsibility is assumed by rf micro devices, inc. ("rfmd") for its use, nor for any infringement of patents, or other rights of third parties, resulting from its use. no license is granted by implication or otherwise under any patent or patent rights of rfmd. rfmd reserves the right to change component circuitry, recommended appli- cation circuitry and specifications at any time without prior notice.
3 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. parameter specification unit condition min. typ. max. wlan ieee802.11b/g, cont. nominal condition t=25 c, v cc =3.3v, 4.2v, and 5v, v reg =2.85v, freq=2450mhz, duty cycle 10 to 100% unless otherwise noted output p1db 33 dbm at nominal conditions with cw signal and v cc =5.0v 32 dbm at nominal conditions with cw signal and v cc =4.2v 30.5 dbm at nominal conditions with cw signal and v cc =3.3v power down pa is ?off? 0.6 v cc pin 3 (pdown) voltage<0.6v dc pa is ?on? 1.75 2.85 5.0 v dc pin 3 (pdown) voltage<0.6v dc power supply operating voltage 3 to 5 v current consumption 500 ma rf p out =+26dbm and v cc =5.0v 200 ma idle current, no rf and v cc =5.0v 425 ma rf p out =+25dbm and v cc =4.2v 180 ma idle current, no rf and v cc =4.2v 370 ma rf p out =+23.5dbm and v cc =3.3v 170 ma idle current, no rf and v cc =3.3v power down current 10 ma v reg =0.0v power down current leakage 1 ma p down =low, v reg =high vreg1, 2, 3 voltage 2.75 2.85 3 vdc higher v reg voltage is possible but with adjust- ing the series resistors to keep the voltage con- stant at the pins. 10 ma i_reg current wimax ieee802.16e nominal condition t=25 c, v cc =3.3v, 4.2v, 5v, v reg =2.85v, freq=2600mhz, duty cycle 1 to 100% unless otherwise noted frequency range 2500 2700 mhz compliance ieee802.16e output power 26 dbm measured standard ieee802.16e waveform (16qam, 10mhz bw), v cc =5.0v evm 2 tbd % rms, mean output power 25 dbm measured standard ieee802.16e waveform (16qam, 10mhz bw), v cc =4.2v evm 2 tbd % rms, mean output power 23.5 dbm measured standard ieee802.16e waveform (16qam, 10mhz bw), v cc =3.3v evm 3 tbd % rms, mean gain 32 db at nominal condition and v cc =5.0v 32 db at nominal condition and v cc =4.2v 32 db at nominal condition and v cc =3.3v gain variation over temperature 1.5 db -10c to +85c input impedance 50 input matched to 50
4 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. parameter specification unit condition min. typ. max. wimax ieee802.16e, cont. nominal condition t=25 c, v cc =3.3v, 4.2v, 5v, v reg =2.85v, freq=2600mhz, duty cycle 1 to 100% unless otherwise noted output p1db 33 dbm at nominal conditions with cw signal and v cc =5.0v 32 dbm at nominal conditions with cw signal and v cc =4.2v 30.5 dbm at nominal conditions with cw signal and v cc =3.3v power down pa is ?off? 0.6 v cc pin 3 (pdown) voltage<0.6v dc pa is ?on? 1.75 2.85 5.0 v dc pin 3 (pdown) voltage<0.6v dc power supply operating voltage 3 to 5 v current consumption 500 ma rf p out =+26dbm and v cc =5.0v 200 ma idle current, no rf and v cc =5.0v 425 ma rf p out =+25dbm and v cc =4.2v 180 ma idle current, no rf and v cc =4.2v 370 ma rf p out =+23.5dbm and v cc =3.3v 170 ma idle current, no rf and v cc =3.3v power down current 10 ma v reg =0.0v power detect leakage current 1 ma p down =low, v reg =high vreg1, 2, 3 voltage 2.75 2.85 3 v dc higher v reg voltage is possible but with adjust- ing the series resistors to keep the voltage con- stant at the pins. 10 ma i_reg current
5 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. parameter specification unit condition min. typ. max. wibro ieee802.16e nominal condition t=25 c, v cc =3.3v, 4.2v, 5.0v, v reg =2.85v, freq=2350mhz, duty cycle 1 to 100% unless otherwise noted frequency range 2300 2400 mhz compliance ieee802.16e output power 26 dbm measured standard ieee802.16e waveform (16qam, 10mhz bw), v cc =5.0v evm 2 tbd % rms, mean output power 25 dbm measured standard ieee802.16e waveform (16qam, 10mhz bw), v cc =4.2v evm 2 tbd % rms, mean output power 23.5 dbm measured standard ieee802.16e waveform (16qam, 10mhz bw), v cc =3.3v evm 3 tbd % rms, mean gain 34 db at nominal condition and v cc =5.0v 34 db at nominal condition and v cc =4.2v 34 db at nominal condition and v cc =3.3v gain variation over temperature 1.5 db -10c to +85c input impedance 50 input matched to 50 output p1db 33 dbm at nominal conditions with cw signal and v cc =5.0v 32 dbm at nominal conditions with cw signal and v cc =4.2v 30.5 dbm at nominal conditions with cw signal and v cc =3.3v power down pa is off 0.6 v cc pin 3 (pdown) voltage<0.6v dc pa is on 1.75 2.85 5.0 v dc pin 3 (pdown) voltage<0.6v dc power supply operating voltage 3 to 5 v current consumption 500 ma rf p out =+26dbm and v cc =5.0v 200 ma idle current, no rf and v cc =5.0v 425 ma rf p out =+25dbm and v cc =4.2v 180 ma idle current, no rf and v cc =4.2v 370 ma rf p out =+23.5dbm and v cc =3.3v 170 ma idle current, no rf and v cc =3.3v power down current 10 ma v reg =0.0v power down current leakage 1 ma p down =low, v reg =high vreg1, 2, 3 voltage 2.75 2.85 3 v dc higher v reg voltage is possible but with adjust- ing the series resistors to keep the voltage con- stant at the pins. 10 ma i_reg current
6 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. pin function description 1bias vcc supply voltage for the bias reference and control circuits. may be connected with vcc1 and vcc2 as long as v cc does not exceed 5.0v dc in this configuration. 2rf in rf input. 3pdown power down pin. apply <0.6v dc to power down the three power amplifier stages. apply 2.5v dc to 3.5v dc to power up. if function is not desired, pin may be connected to v cc or v reg . 4vreg1 first stage input bias voltage. this pin requires a regulated supply to maintain nominal bias current. 5vreg2 second stage input bias voltage. this pin requires a regulated supply to maintain nominal bias current. 6vreg3 third stage input bias voltage. this pin requires a regulated supply to maintain nominal bias current. 7nc not connected. may be connected to ground. 8p detect power detector provides an output voltage proportional to the rf output power level. 9 not connected. may be connected to ground. 10 vcc3/ rf out rf output and bias for the output stage. output is externally matched to 50 and needs dc block. 11 vcc3/ rf out same as pin 10. 12 vcc3/ rf out same as pin 10. 13 vcc2 second stage supply voltage. 14 vcc2 same as pin 13. 15 nc not connected. may be connected to ground. 16 vcc1 first stage supply voltage. pkg base gnd ground connection. the back side of the package should be connected to the ground plane through as short a connection as possible, e.g., pcb vias under the device are recommended.
7 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. package outline notes: 1. dimension applies to metallized terminal and is measured between 0.25mm and 0.30mm from terminal tip. 2. dimension represents terminal pull back from package edge up to 0.1mm is acceptable. 3. complanarity applies to the exposed heat slug, as well as the terminal. 4. radius on terminal is optional.
8 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. pin out pdown rf in bias vcc nc vreg1 vreg2 vreg3 nc pdetect rf out/vcc3 vcc1 vcc2 vcc2 rf out/vcc3 rf out/vcc3 16 15 14 13 5 6 7 8 9 10 11 12 4 3 2 1 nc
9 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. evaluation board schematic wlan 2.4ghz to 2.5ghz operation 15 14 13 12 11 10 4 3 2 1 16 9 8 7 6 5 50 strip j1 rf in r1 560 r3 56 c19 2 pf c9 2 pf 38 strip j2 rf out l6 3.9 nh c16 1 uf c1 1000 pf c13 4.7 pf c11 1 f l3 12 nh c8 1 pf pdown l5 1.8 nh 50 strip c17 10 uf r4 0 voltage r4 value in ohms 5.0 27 3.3 0 38 strip c2 1 nf r2 180 vreg pdet c7 330 pf c3 0.7 pf
10 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. evaluation board schematic wimax 2.5ghz to 2.7ghz operation 15 14 13 12 11 10 4 3 2 1 16 9 8 7 6 5 50 strip j1 rf in r1 560 r3 56 c19 2 pf c9 2 pf 38 strip j2 rf out l6 3.9 nh c16 1 f c1 1000 pf c13 3.9 pf c11 1 uf vreg l3 3.9 nh c8 1 pf pdown r2 180 l5 1.8 nh 50 strip c17 10 uf r4 0 voltage r4 value in ohms 5.0 27 3.3 0 38 strip pdet c7 330 pf c2 1 nf c3 0.7 pf
11 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. evaluation board schematic wibro 2.3ghz to 2.4ghz operation 15 14 13 12 11 10 4 3 2 1 16 9 8 7 6 5 50 strip j1 rf in r1 560 r3 56 c7 330 pf pdetect c19 2 pf c9 2 pf 38 strip j2 rf out l6 3.9 nh c16 1 f c1 1000 pf c13 5.1 pf c11 1 f vreg p1 1 2 hdr_1x2 gnd vcc p1-1 l3 12 nh vreg3 p2-2 p2 1 2 3 4 5 hdr_1x6 gnd p_detect p2-1 vreg2 p2-4 vreg1 p2-5 c8 1 pf pdown l5 1.8 nh 50 strip c17 10 uf + r4 0 voltage r4 value in ohms 5.0 27 3.3 0 38 strip r2 180 hf 0.7 pf
12 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. wlan 2.4ghz to 2.5ghz operation 100% wlan evm and gt versus p out , 2.4ghz to 2.5ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 3.3v - 2.4ghz 3.3v - 2.45ghz 3.3v - 2.5ghz 3.3v - 2.4ghz 3.3v - 2.45ghz 3.3v - 2.5ghz 100% wlan evm and gt versus p out, 2.4 ghz to 2.5ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 4.2v - 2.4ghz 4.2v - 2.45ghz 4.2v - 2.5ghz 4.2v - 2.4ghz 4.2v - 2.45ghz 4.2v - 2.5ghz i cc versus p out , 2.4ghz to 2.5ghz tune 0.0 0.2 0.4 0.6 0.8 1.0 8 101214161820222426283032 p out (dbm) i cc (a) 3.3v - 2.4ghz 3.3v - 2.45ghz 3.3v - 2.5ghz i cc versus p out , 2.4ghz to 2.5ghz tune 0.0 0.2 0.4 0.6 0.8 1.0 8 101214161820222426283032 p out (dbm) i cc (a) 4.2v - 2.4ghz 4.2v - 2.45ghz 4.2v - 2.5ghz p detect versus p out , 2.4ghz to 2.5ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 8 101214161820222426283032 p out (dbm) p detect (v) 3.3v - 2.4ghz 3.3v - 2.45ghz 3.3v - 2.5ghz p detect versus p out , 2.4ghz to 2.5ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 8 101214161820222426283032 p out (dbm) p detect (v) 4.2v - 2.4ghz 4.2v - 2.45ghz 4.2v - 2.5ghz
13 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. wlan evm and gain versus p out 2.4ghz to 2.5ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 gain (db) 5v - 2.4ghz 5v - 2.45ghz 5v - 2.5ghz 5v - 2.4ghz 5v - 2.45ghz 5v - 2.5ghz wlan i cc versus p out 2.4ghz to 2.5ghz tune 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 10 12 14 16 18 20 22 24 26 28 30 32 p out (dbm) i cc (a) 5v 2.4ghz 5v 2.5ghz 5v 2.45ghz wlan pdet versus p out 2.4ghz to 2.5ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 10 12 14 16 18 20 22 24 26 28 30 32 p out (dbm) pdet (v) 5v 2.4ghz 5v 2.45ghz 5v 2.5ghz
14 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. wibro 2.3ghz to 2.4ghz operation wimax evm and gt versus p out, 2.3 ghz to 2.4ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 3.3v - 2.3ghz 3.3v - 2.35ghz 3.3v - 2.4ghz 3.3v - 2.3ghz 3.3v - 2.35ghz 3.3v - 2.4ghz wimax evm and gt versus p out, 2.3ghz to 2.4ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 4.2v - 2.3ghz 4.2v - 2.35ghz 4.2v - 2.4ghz 4.2v - 2.3ghz 4.2v - 2.35ghz 4.2v - 2.4ghz i cc versus p out , 2.3ghz to 2.4ghz tune 0.0 0.2 0.4 0.6 0.8 1.0 8 101214161820222426283032 p out (dbm) i cc (a) 3.3v - 2.3ghz 3.3v - 2.35ghz 3.3v - 2.4ghz i cc versus p out , 2.3ghz to 2.4ghz tune 0.0 0.2 0.4 0.6 0.8 1.0 8 101214161820222426283032 p out (dbm) i cc (a) 4.2v - 2.3ghz 4.2v - 2.45ghz 4.2v - 2.5ghz p detect versus p out , 2.3ghz to 2.4ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 8 101214161820222426283032 p out (dbm) p detect (v) 3.3v - 2.3ghz 3.3v - 2.35ghz 3.3v - 2.4ghz p detect versus p out , 2.3ghz to 2.4ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 8 101214161820222426283032 p out (dbm) p detect (v) 4.2v - 2.3ghz 4.2v - 2.35ghz 4.2v - 2.4ghz
15 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. wibro i cc versus p out 2.3ghz to 2.4ghz tune 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 10 12 14 16 18 20 22 24 26 28 30 32 p out (dbm) i cc (a) 5v 2.3ghz 5v 2.35ghz 5v 2.4ghz wibro pdet versus p out 2.3ghz to 2.4ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 10 12 14 16 18 20 22 24 26 28 30 32 p out (dbm) p det (v) 5v 2.3ghz 5v 2.35ghz 5v 2.4ghz wibro evm and gain versus p out 2.3ghz to 2.4ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 gain (db) 5v - 2.3ghz 5v - 2.35ghz 5v - 2.4ghz 5v - 2.3ghz 5v - 2.35ghz 5v - 2.4ghz
16 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. wimax 2.5ghz to 2.7ghz operation wimax evm and gt versus p out, 2.5ghz to 2.7ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 3.3v - 2.5ghz 3.3v - 2.6ghz 3.3v - 2.7ghz 3.3v - 2.5ghz 3.3v - 2.6ghz 3.3v - 2.7ghz wimax evm and gt versus p out , 2.5ghz to 2.7ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 4.2v - 2.5ghz 4.2v - 2.6ghz 4.2v - 2.7ghz 4.2v - 2.5ghz 4.2v - 2.6ghz 4.2v - 2.7ghz i cc versus p out , 2.5ghz to 2.7ghz tune 0.0 0.2 0.4 0.6 0.8 1.0 8 101214161820222426283032 p out (dbm) i cc (a) 4.2v - 2.5ghz 4.2v - 2.6ghz 4.2v - 2.7ghz p detect versus p out , 2.5ghz to 2.7ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 8 101214161820222426283032 p out (dbm) p detect (v) 3.3v - 2.5ghz 3.3v - 2.6ghz 3.3v - 2.7ghz p detect versus p out , 2.5ghz to 2.7ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 8 101214161820222426283032 p out (dbm) p detect (v) 4.2v - 2.5ghz 4.2v - 2.6ghz 4.2v - 2.7ghz i cc versus p out , 2.5ghz to 2.7ghz tune 0.0 0.2 0.4 0.6 0.8 1.0 8 101214161820222426283032 p out (dbm) i cc (a) 3.3v - 2.5ghz 3.3v - 2.6ghz 3.3v - 2.7ghz
17 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com. wimax evm and gain versus p out 2.5ghz to 2.7ghz tune 0 1 2 3 4 5 6 7 8 8 101214161820222426283032 p out (dbm) evm (%) 25 26 27 28 29 30 31 32 33 34 35 gain (db) 5v - 2.5ghz 5v - 2.6ghz 5v - 2.7ghz 5v - 2.5ghz 5v - 2.6ghz 5v - 2.7ghz wimax i cc versus p out 2.3ghz to 2.4 ghz tune 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 10 12 14 16 18 20 22 24 26 28 30 32 p out (dbm) i cc (a) 5v 2.5ghz 5v 2.6ghz 5v 2.7ghz wimax pdet versus p out 2.5ghz to 2.7ghz tune 0.0 0.5 1.0 1.5 2.0 2.5 3.0 10 12 14 16 18 20 22 24 26 28 30 32 p out (dbm) pdet (v) 5v 2.5ghz 5v 2.6ghz 5v 2.7ghz
18 of 18 RF5602 proposed prelim ds090427 7628 thorndike road, greensboro, nc 27409-9421 for sales or technical support, contact rfmd at (+1) 336-678-5570 or sales-support@rfmd.com.

▲Up To Search▲

Price & Availability of RF5602

	To Download RF5602 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .